American Standard Amarilis Lexington Bath Filler 8971 Series User Manual download pdf

M66232 Rev.1.1

LEXINGTON DECK-MOUNT

BATH FILLERS

Installation

Instructions

8970 SERIES

8971 SERIES

Certiﬁed to comply with ANSI A112.18.1M.

U.S. Patent No. 5,819,789



Congratulations on purchasing your American Standard faucet with

EverClean nish found only on American Standard faucets.

To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.

with EverClean™ Finish

*Hex key

*Supplied with Fitting

Flat Blade Screwdriver

Adjustable Wrench

Channel Locks

Phillips Screwdriver

Required Tools

VALVE INSTALLATION

5VCJOH$VUUFS

EverClean Finish

• One wipe effortlessly removes spots

• Eliminates the need for cleaners and scrubbing

• Permanent surface protectant remains beautiful

for the life of the faucet

• EverClean™ available on: Polished Chrome, Satin Nickel,

Stainless Steel, Polished Brass (or any combination of these finishes)

IMPORTANT NOTICE TO INSTALLER!

Please check with local Code Authority for the installation requirements of this product. Some codes require an additional

temperature mixing valve to limit the maximum hot water temperature and vacuum breaker (for products with hand spray)

to be installed with this product.

Insert SPOUT SHANK (1) through center hole of bath tub LEDGE.

Make sure that the RUBBER RING (2) is properly seated in recess

at base of SPOUT (6).

Attach RUBBER WASHER (3) and BRASS WASHER (4) to SHANK (1)

from underside of ledge and secure SPOUT (6) position with LOCKNUT (5).

SPOUT INSTALLATION

O-RING



Turn off hot and cold water

supplies before beginning.

CAUTION

Prepare TUBE and TEE ASSEMBLY (1) to ﬁt existing VALVE (2) location (between 6-1/2"

and12"). If necessary, cut and/or bend TUBING (3) carefully. Make sure tube bend

is close to the TEE (4) so that it will not effect the compression joint at the VALVE (2).

Remove COUPLING NUT (5) and FERRULE (6) from each VALVE (2)

and slide onto TUBING (3).

Push TUBING (3) ends into VALVE (2) side outlets. Insert VALVES (2)

into mounting holes from underside of ledge.

Press TEE (4) onto SPOUT SHANK (7) making certain that the O-RING (8)

is properly seated on SHANK (7).

Place RUBBER RING (9) into ESCUTCHEON (10) and screw ESCUTCHEON (10)

onto valve until snug against internal stop.

Tighten LOCKNUT (12) to secure VALVE (2) position. Attach COUPLING (11 or 11a)

to TEE (4) and tighten. Note: For product with Hand Shower, COUPLING (11)

is tightened using a 10mm (3/8”) Hex Wrench.

Slide FERRULE (6) and COUPLING NUT (5) to outlet of VALVE (2)

and tighten COUPLING NUT (5) ﬁrmly.

Connect HOT water supply to inlet of left VALVE and COLD water supply to

inlet of right VALVE using appropriate connector.

SPOUT

HOT

COLD

HANDLE

SCREW

11a

1 2

Summary of Contents

Page 1 - Instructions

M66232 Rev.1.1LEXINGTON DECK-MOUNTBATH FILLERSInstallationInstructions8970 SERIES8971 SERIESCertiﬁed to comply with ANSI A112.18.1M.U.S. Patent No. 5,

Page 2 - TEST INSTALLED FAUCET

M66232 Rev.1.1HANDSHOWER INSTALLATION (Mode 8971 series only)SERVICETEST INSTALLED FAUCETTo change direction of handle rotation, proceed as follows

Comments to this Manuals

No comments

American Standard Amarilis Lexington Bath Filler 8971 Series User Manual

Browse online or download User Manual for Sanitary ware American Standard Amarilis Lexington Bath Filler 8971 Series. American Standard Amarilis Lexington Bath Filler 8971 Series User's Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Sanitary ware American Standard Amarilis Lexington Bath Filler 8971 Series