American Standard 3875.501.002 Installation Guide download pdf

COLONY SOFT

3875.409

3875.509

SLOT

MOUNTING

SURFACE

Turn off hot and cold water

supplies before beginning.

CAUTION

Insert SPOUT (1) and CABLE CONNECTOR (2) through center hole, making sure

the and SEAL WASHER (3) is properly seated in SPOUT (1).

Assemble RUBBER WASHER (4), BRASS WASHER (5) and LOCKNUT (6) onto SPOUT

SHANK (7) from under side of sink . Make sure SPOUT (1) is centered in the mounting

hole and the slot in the BRASS WASHER (5) faces toward the rear of the sink.

Tighten LOCKNUT (6) ﬁrmly. Fig. A.

Hand tighten LOCKNUT (11) to secure VALVE BODY (12). Repeat above steps

for opposite VALVE BODY (12A).

Install LOCKNUT (11) onto VALVE BODY (12).

From under side of mounting surface, install VALVE BODY (12) through valve

mounting holes. Threads of VALVE BODY (12) should extent at least 5/16

of a inch above mounting surface top. Fig. B. Thread ESCUTCHEON (10)

onto VALVE BODY (12) until snug against internal stop. If necessary, adjust

LOCKNUT (11).

Certiﬁed to comply with ANSI A112.18.1

Installation

Instructions

Spread Lavatory Faucet with

INSTALL SPOUT

INSTALL VALVE BODY

12a

Place RUBBER RING (9) into SCUTCHEON (10).

5/16'' MIN.

Speed Connect™ Drain

Adjustable Wrench Screwdriver Channel Locks

Recommended tools

Tubing Cutter

Congratulations on purchasing your American Standard faucet with the

Speed Connect drain, a features found only on American Standard faucets.

*Your new American Standard faucet is designed to work only with the Speed Connect drain.

To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.

Fig. A.

Fig. B.

M968887 Rev.1.1

Speed Connect Drain*

• Fewer parts, installs in less time

• Never needs adjustment

• Guaranteed to seal properly the ﬁrst time, every time.

1 2 3 4 5 6 7

Summary of Contents

Page 1 - Instructions

COLONY SOFT3875.4093875.509465SLOTMOUNTINGSURFACETurn off hot and cold watersupplies before beginning.CAUTIONInsert SPOUT (1) and CABLE CONNECTOR (2)

Page 2 - REAR OF SINK

M968887 Rev.1.1 6POP-UP KNOB (1) must be fully down. Fig. B. FLANGE GASKET AND POP-UP KNOBDOWNWHITE FOAMGASKETNOT VISIBLEDRAINFLANGEFig. A. Fig. B.

Page 3 - CHECK OPERATION OF POP-UP

Connect HOT water supply to inlet of left SHANK and COLDwater supply to right SHANK using sealant, appropriateconnectors, and COUPLING NUTS.Connect 1-

Page 4 - “P” TRAP

CHECK DRAIN CONNECTIONS111213TEST INSTALLED FITTINGWith HANDLES (1) in OFF position, turn on WATERSUPPLIES (2) and check all connections for leaks.Rem

Page 5 - SpeedConnect™ Drain

M968887 Rev.1.1 SpeedConnect™ DrainTroubleshooting GuideDisconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise.

Page 6 - M968887 Rev.1.1

M968887 Rev.1.1 STOPPER INSTALLATION PROCEDURELocked Mode: Look at the Plastic Loop at the bottom of the Stopper and noticethat the Loop is on one s

Page 7 - COLONY SOFT

024220-0070ASUPPLY NUTM906617-0070AATTACHMENT NUTA954120-0070AVALVEM904900-0070AVALVE NUTM918021-0070AADAPTERM950157-YYY0APOP-UP RODM918504-0070ASCREW

Comments to this Manuals

No comments

American Standard 3875.501.002 Installation Guide

Browse online or download Installation Guide for Sanitary ware American Standard 3875.501.002. American Standard 3875.501.002 Installation Guide User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Sanitary ware American Standard 3875.501.002