American Standard 2506921.002 Installation Guide download pdf

SEAL

DECK MOUNT BATH FILLER

MOMENTS

Certiﬁed to comply with ANSI A112.18.1M

Recommended Tools

*Supplied with Fitting

*Hex key

Turn off hot and cold water

supplies before beginning.

CAUTION

Insert SPOUT SHANK (1) through center hole of MOUNTING SURFACE.

Important: Set screw slot in SPOUT SHANK (1) must face back of ﬁtting. View A.

Install SPOUT ESCUTCHEON AND SEAL (5) onto SPOUT SHANK (1).

SPOUT AND VALVE ASSEMBLY

Flat Blade Screwdriver

Adjustable Wrench

Channel Locks

ROUGHING-IN DIMENSIONS

Installation

Instructions

2506.921

2506.920

Tubing Cutter

Sealing Tape

M968694 Rev.1.5

MOUNTING

SURFACE

7-7/8"

(200mm)

3-3/4"

(96mm)

9-7/8"

(250mm)

9-3/4"

(247mm)

1-3/8"

(35mm)

1-1/2

MAX.

(38mm) MAX.

1-3/16" MAX.

(30mm) MAX.

1-3/16

(30mm) D.

(76mm)

(H)

(C)

1-1/8

2-3/8

(59mm)

MAX.

(305mm)

1-1/16

(27mm) D.

3/4-14 MALE

N.P.S.M. INLETS

6-1/2" to 12"

(165mm to 305mm)

Thread MOUNTING RING NUTS (6) counter clock-wise to allow enough

space for the thickness of the mounting surface.

Adjust the three LOCKING SCREWS (7) so that they extend about 1/2 inch

above the MOUNTING RING NUTS (6). Install MOUNTING WASHERS (8) and

RUBBER WASHERS (9) onto VALVE BODIES. Thread VALVE BODY (10) with

red band into the left side (hot) of the VALVE ESCUTCHEON (11) until it’s

seated against the stop. Thread the (cold) VALVE BODY (10a) into the opposite

VALVE ESCUTCHEON (11).

Hand tighten the MOUNTING RING NUTS (6) on valve bodies.

Adjust valve outlets to face the SPOUT SHANK (1).

With a ﬂate blade screwdriver alternetly tighten the three LOCKING

SCREWS (7) to secure the valve bodies. Make sure there is equal

pressure on all LOCKING SCREWS (7).

1-1/8'' MAX.

MOUNTING

SURFACE

DETAIL OF VALVE ASSEMBLY

11, 11a

1/2''

10a

RED BAND

INSTALL

VALVE OUTLET

SLOT

VIEW "A"

Assemble RUBBER WASHER (2) and BRASS WASHER (3) onto SPOUT SHANK (1).

From underside of ledge secure SPOUT SHANK (1) into position with LOCKNUT (4).

Thank you for selecting American-Standard...the benchmark

of ﬁne quality for over 100 years.

To ensure that your installation proceeds smoothly--please

read these instructions carefully before you begin.

2-1/16

DIA.

7-7/8"

(200mm)

1 2 3 4

Summary of Contents

Page 1 - Instructions

SEALDECK MOUNT BATH FILLERMOMENTSCertiﬁed to comply with ANSI A112.18.1MRecommended Tools*Supplied with Fitting*Hex keyTurn off hot and cold watersupp

Page 2 - 3/4" NPT

2Press TEE (1) onto SPOUT SHANK (2) making certain thatthe O-RING (3) is properly seated on SHANK (2).Push COUPLING (4) into TEE (1) and thread onto S

Page 3 - TRANSFER KNOB

HANDSHOWER78 9With HANDLES in OFF position, turn on WATER SUPPLIES andcheck all connections for leaks.Operate both HANDLES to ﬂush water lines thoroug

Page 4 - HOT LINE FOR HELP

A900812-0070ATEEDECK-MOUNTBATH FILLERM962584-0070ASHANK KIT030274-0070ASHANK MOUNTING KITM962585-YYY0ASPOUT ESCUTCHEON KITMODEL NUMBER028699-0070ACOU