American-standard Swan 6011 User Manual download pdf

IN WALL PRESSURE BALANCING

BATH AND SHOWER SETS

To assure proper positioning in relation to wall,

note roughing-in dimensions.

Thank you for selecting American-Standard...the benchmark of fine

quality for over 100 years.

To ensure that your installation proceeds smoothly--please read these

instructions carefully before you begin.

ROUGHING-IN DIMENSIONS

Certified to comply with ANSI A112.18.1

Installation

Instructions

SWAN

6011

6012

THREADED INLETS (STOPS)

INLETS

1/2" NPT

5-7/8"

INLETS 1/2" NPT

OUTLETS

1/2" NPT

OUTLETS

1/2" NPT

3-3/8"

THREADED INLETS

Required Tools

Flat Blade Screwdriver

Adjustable Wrench

Channel Locks

Plumbers' Putty or Caulking

Phillips Screwdriver

ROUGHING-IN

Turn off water at main supply.

CAUTION

When soldering, remove PLASTER GUARD, CARTRIDGES and CHECK STOPS (IF PRESENT). When finished soldering,

flush valve body, replace cartridges, check stops (if present) and plaster guard to continue installation. Use thread

sealant or Teflon tape on threaded connections.

NOTE

If the valve is installed on a fiberglass

or other thin wall application, the

PLASTER GUARD (4) can be used as a support.

Connect hot and cold water supplies.

Cap off shower pipe (5) and tub filler pipe (6).

For support, use pipe BRACES (7) secured to wooden braces.

With valve turned off, turn on water supplies. Check for leaks.

COLD

HOT

Cut a 4" dia. hole in the shower stall.

Drill two additional 1" holes to allow access

to the stops.

Remove PLASTER GUARD (4), rotate 90˚

so that indicated screw holes fit MANIFOLD (2).

Push CAP on valve, place ESCUTCHEON on and

attach with screws.

See Roughing-in diagram before starting.

Connections are:

1/2" female NPT for threaded inlets

Connect RISER PIPE (1) to MANIFOLD (2)

top outlet marked "SHR".

Connect TUB FILLER PIPE (3) at bottom

outlet marked "TUB".

For proper positioning the finished wall

must be within side wall of PLASTER

GUARD (4).

FINISHED WALL

BOTTOM OF TUB

74" FOR HEAD

CLEARANCE

18" OPTIONAL

5" REF.

1/2" NPT

1-5/8"

3-1/4"

7-1/8"

1-1/2"

MIN.

OPTIONAL TO FINISHED

FLOOR USUALLY

BETWEEN 65'' AND 80''

TOP OF TUB RIM

4" REF.

5-1/2" REF.

M968462S-O

1/2" COPPER

SLIP-ON

SPOUT

Tubing Cutter

1 2 3 4

Summary of Contents

Page 1 - Instructions

IN WALL PRESSURE BALANCINGBATH AND SHOWER SETSTo assure proper positioning in relation to wall,note roughing-in dimensions. Thank you for selecting Am

Page 2

3INSTALL HANDLEADJUST HOT LIMIT STOPBy restricting HANDLE rotation and limiting the amount of hotwater allowed to mix with the cold, the HOT LIMIT SAF

Page 3 - A COARSE SURFACE

5Remove handle SET SCREW, remove HANDLE, unscrew HANDLE SCREW and remove ADAPTER.Remove two SCREWS holding ESCUTCHEON and remove ESCUTCHEON.Remove COV

Page 4 - BATH AND SHOWER SETS

A954440-0070ACARTRIDGE023603-0070ACARTRIDGE SCREWSA923611-0070AHOT LIMIT STOPM961854-0070AFIXATION RING WITH SCREWSM952100-0070APRESSURE BALANCING UNI

Comments to this Manuals

No comments

American-standard Swan 6011 User Manual

Browse online or download User Manual for Accessories for water American-standard Swan 6011. American Standard Swan 6011 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Accessories for water American-standard Swan 6011