American Standard Single Control Kitchen Faucet with Cast Spout 3821.644 Series User Manual

Browse online or download User Manual for Sanitary ware American Standard Single Control Kitchen Faucet with Cast Spout 3821.644 Series. American Standard Single Control Kitchen Faucet with Cast Spout 3821.644 Series User's Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 4
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
SINGLE CONTROL KITCHEN
FAUCET WITH CAST SPOUT
Installation
Instructions
M968188E
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
Certified to comply with ANSI A112.18.1M
3821.631 SERIES
3821.641 SERIES
3821.634 SERIES
3821.644 SERIES
1
2
3
4
5
6
7
8
A
B
9
CAUTION
1
INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON
Turn off hot and cold water supplies before beginning.
PUTTY
SPOUT BASE
SPOUT BASE
SINK OR
MOUNTING
SURFACE
Assemble RUBBER WASHER (5), BRASS WASHER (6), and threaded LOCKNUT (7) onto SHANK (4) from underside
of sink or mounting surface. Hand tighten LOCKNUT (7) and check that rotation of HANDLE (8) from HOT to COLD
is centered.
Push O-RINGS (2) onto SPOUT SHANK. Make certain the O-RING (2) is properly seated in recess of DECORATIVE
FLANGE (10).
Insert SUPPLY TUBES (3) and SHANK (4) through mounting hole and seat DECORATIVE FLANGE (10) onto sink or
mounting surface.
Use a screwdriver to tighten SCREWS (9) on LOCKNUT (7). Work your way around LOCKNUT (7), tightening
the screws slightly each time until all are snug to ensure even pressure.
(A) Installation with ESCUTCHEON (1).
Apply a bead of putty to bottom edge of ESCUTCHEON (1). Insert supply
TUBES (3) and SHANK (4) through hole of ESCUTCHEON (1) and mounting surface. Make certain the O-RING (2)
is properly seated in recess of SPOUT BASE. Follow mounting instructions below to secure faucet to mounting surface.
(B) Installation less ESCUTCHEON (1).
Remove ESCUTCHEON (1) , feed FAUCET TUBES (3) and SHANK (4) through
DECORATIVE FLANGE (10). Push FLANGE so the raised step fits into recess of SPOUT BASE.
Plumbers' Putty or Caulking
Adjustable Wrench
Phillips Screwdriver
Channel Locks
TOOLS REQUIRED
Tubing Cutter
2
3
4
5
6
7
9
10
Regular Screwdriver
8
Page view 0
1 2 3 4

Summary of Contents

Page 1 - Instructions

SINGLE CONTROL KITCHENFAUCET WITH CAST SPOUTInstallationInstructionsM968188EThank you for selecting American-Standard...the benchmarkof fine quality f

Page 2

M968188EOn model with separate spray, place the SPRAY HOLDER (1)into the appropriate mounting hole. Assemble the SPRAYHOLDER WING NUT (2) onto the sha

Page 3 - CARE INSTRUCTIONS

M968188E5TEST INSTALLED FAUCETMove HANDLE down into "off" position and remove AERATOR.Turn on water supplies and check connections for leaks

Page 4 - FAUCET WITH CAST SPOUT

M968188E MODEL NUMBERSSINGLE CONTROL KITCHENFAUCET WITH CAST SPOUT042850-0070ADIVERTER060366-0070ASPOUT SEAL KIT912647-0070AO-RING SEAL921877-0070ACAP

Comments to this Manuals

No comments