American Standard NEW SAVONA 2097.012 User Manual download pdf

RECOMMENDED TOOLS AND MATERIALS

Putty Knife Regular Screwdriver Adjustable Wrench Sealant Tape Measure

Hacksaw Wax Ring/Gasket Flexible Supply Tube Closet Bolts Carpenters Level

1 REMOVE OLD TOILET

a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.

b. Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!

c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.

d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.

NOTE: Mounting surface must be clean and level before new toilet is installed!

SAVE FOR FUTURE USE

CLOSET

FLANGE

CLOSET

BOLTS

7301387-100

CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!

Product names listed herein are trademarks of AS America, Inc.

NOTE: Pictures may not exactly define contour of china and components.

NEW SAVONA 1.6 GPF ONE-PIECE TOILET

ROUGHING-IN DIMENSIONS:

NOTE: Distance from wall to closet flange centerline must be as listed below:

INSTALL WAX SEAL

Invert toilet on floor (cushion to prevent damage), and

install wax ring evenly around waste flange (horn), with

tapered end of ring facing toilet. Apply a thin bead of

sealant around toilet base.

POSITION TOILET ON FLANGE

a. Unplug floor waste opening and install toilet on closet flange so bolts project

through mounting holes.

b. Loosely install retainer washers and nuts. Side of washers marked "THIS

SIDE UP" must face up!

WAX RING

SEALANT

WASHER

NUT

FLANGE

BOLT

Model 2097.012

Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed

properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure

your installation conforms to local codes.

INSTALL CLOSET BOLTS

Install closet bolts in flange channel, turn 90

, and slide

into place 6" (152 mm) apart and parallel to wall.

INSTALLATION INSTRUCTIONS

FINISHED WALL

79mm

(7-1/8)

13mm

(1/2)

23mm

(7/8)

C/L OF SEAT POST

HOLES 140mm

(5-1/2) CTR'S.

305mm

(12)

C/L

C/L OF SUPPLY

AS REQUIRED

FINISHED

FLOOR

176mm

(7)

736mm

(29)

473mm

(18-1/2)

140mm

(5-1/2)

203mm

(8)

343mm

(13-1/2)

305mm

(12)

384mm

(15)

767mm

(30-1/4)

388mm

(15-5/16)

413mm

(16-1/4)

355mm

(14)

1 2 3 4

Summary of Contents

Page 1 - INSTALLATION INSTRUCTIONS

RECOMMENDED TOOLS AND MATERIALSPutty Knife Regular Screwdriver Adjustable Wrench Sealant Tape MeasureHacksaw Wax Ring/Gasket Flex

Page 2 - PLASTIC SUPPLY LINE

7301387-10067INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer's directions.- 2 - 8a8bBefore continuing, determine the typ

Page 3 - NEW SAVONA ONE-PIECE TOILET

7301387-1009 10ADJUSTMENTS a. Adjust water level. Water level should be adjusted to level indicated on tank by adjusting float cup.See Step

Page 4 - San Juan Capistrano, CA 92675

7301387-10012ONE YEAR LIMITED WARRANTYThis limited warranty applies only to the original purchaser and installation of the products. In the event of a

Comments to this Manuals

No comments

American Standard NEW SAVONA 2097.012 User Manual

Browse online or download User Manual for Sanitary ware American Standard NEW SAVONA 2097.012. American Standard NEW SAVONA 2097.012 User's Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Sanitary ware American Standard NEW SAVONA 2097.012