American Standard 2171 User Manual download pdf (Page 1)

Plumbers' Putty or CaulkingAdjustable Wrench Phillips ScrewdriverChannel Locks

TOOLS REQUIRED

MONOBLOCK

LAVATORY FAUCET

SINGLE LEVER

Installation

Instructions

M968291C

Certified to comply with ANSI A112.18.1M

2171

Thank you for selecting American-Standard...the benchmark of fine

quality for over 100 years.

To ensure that your installation proceeds smoothly--please read these

instructions carefully before you begin.

COLLECTION

™

THE

BOSS

GROOVE IN

FAUCET BASE

LAVATORY SINK

OR MOUNTING

SURFACE

No sealant is required unless mounting surface is uneven for 3-hole (4" centers)

installation with ESCUTCHEON PLATE (1). Place ESCUTCHEON PLATE (1) over

mounting holes on lavatory sink or mounting surface.

Insert LIFT ROD (7).

From below, install MOUNTING GASKET with

RETAINING WASHER (5) and Nut (6) onto

STUD (4). Pull Faucet to front of sink, so STUD

(4) rests against sink hole. Before final tightening,

align Faucet and ESCUTCHEON (1) so they are

centered on mounting surface. Tighten NUT (6)

to secure Faucet

From below, install MOUNTING GASKET with

RETAINING WASHER (5) and Nut (6) onto

STUD (4). Pull Faucet to front of sink, so STUD

(4) rests against sink hole. Before final tightening,

align Faucet and ESCUTCHEON (1) so they are

centered on mounting surface. Tighten NUT (6)

to secure Faucet

For single hole installation use ESCUTCHEON

RING (2). Install SEAL WASHER (6) into groove

in ESCUTCHEON RING (2) base and place over

over mounting hole in lavatory sink or mounting

surface.

Insert LIFT ROD (7).

Feed FLEXIBLE FAUCET HOSES (3) and MOUNTING

STUD (4) through hole in ESCUTCHEON RING (2).

Seat ESCUTCHEON RING (2) boss into groove in

Faucet base.

Feed FLEXIBLE FAUCET HOSES (3) and MOUNTING STUD (4) through

hole in ESCUTCHEON PLATE (1). Seat ESCUTCHEON PLATE (1) boss

into groove in Faucet base.

INSTALL FAUCET

Turn off water at

main supply.

CAUTION

INSTALLATION OPTIONS; Faucet may be installed with ESCUTCHEON

PLATE (1) or for center hole only with ESCUTCHEON RING (2).

INSTALLATION with ESCUTCHEON PLATE (1)

INSTALLATION with ESCUTCHEON RING (2)

BOSS

GROOVE IN

ESCUTCHEON

RING BASE

Remove as much surface dirt and film using clear

water and soft cotton cloth (as described above).

Once clean, rinse faucet again with clear water to

thoroughly remove cleaner or polish and blot dry with

a soft cotton cloth.

To keep your new faucet looking new, please follow

these simple care instructions:

DO: Simply rinse the faucet clean with clear water.

Dry the faucet with a soft cotton cloth.

Do not use any abrasive cleaners, cloths, or

paper towels.

Do not use any cleaning agents containing

acids, polish abrasives, or harsh cleaners or

soaps.

Regular and routine cleaning will reduce the need for

heavy cleaning and polishing. If heavy cleaning is

required, the following procedures are recommended:

CARE INSTRUCTIONS:

Failure to follow these care instructions may

damage the Faucet's finish.

DO NOT:

Use any of the following to remove tough surface

film and build-up:

Mild liquid detergents

Clear ammonia free liquid glass cleaners

Non-acidic, non-abrasive gentle liquid or fully

dissolved powder cleansers mixed according to

manufacturers directions.

Non-abrasive liquid polishers

1 2 3 4

Summary of Contents

Page 1 - Instructions

Plumbers' Putty or CaulkingAdjustable Wrench Phillips ScrewdriverChannel LocksTOOLS REQUIREDMONOBLOCK LAVATORY FAUCET SINGLE LEVERInstallationIns

Page 2 - 1-1/4"

M968291C3WATER SUPPLY CONNECTIONSNote: FLEXIBLE HOSES (1, 2) on FAUCET (3) are (17-1/2") inlength from base of faucet. If longer supply length is

Page 3

ADJUST HOT LIMIT STOPBy restricting HANDLE rotation and limiting theamount of hot water allowed to mix with the cold, theHOT LIMIT SAFETY STOP (5) red

Page 4 - SINGLE LEVER

072574-0070AEXTENSION ROD066116-YYY0ADRAIN STOPPERGASKETWASHERLOCKNUTM961711-0070ATAILPIECE INSERTFLANGE070847-0070ACLIP066118-0070APIVOT ROD953450-YY