American Standard Hampton 7881.702 User Manual download pdf

7871 SERIES

SLOT

Turn off hot and cold water

supplies before beginning.

CAUTION

Insert SPOUT (1) and CABLE CONNECTOR (12) through center hole, making sure

the SPOUT ESCUTCHEON (2) and SEAL WASHER (3) are properly seated.

Assemble RUBBER WASHER (4), BRASS WASHER (5) and LOCKNUT (6) onto SPOUT

SHANK (7) from under side of sink . Make sure SPOUT (1) is centered in the mounting

hole and the slot in the BRASS WASHER (5) faces toward the rear of the sink.

Tighten LOCKNUT (6) ﬁrmly. Fig. A.

Certiﬁed to comply with ANSI A112.18.1

Installation

Instructions

Spread Lavatory Faucet with the

INSTALL SPOUT

INSTALL VALVE BODY

Speed Connect™ Drain

Adjustable Wrench Screwdriver Channel Locks

Recommended tools

Tubing Cutter

Fig. A.

US60404 Rev.1.2

7871.702

7871.712

7871.722

7871.732

7881.702

7881.712

7881.722

7881.732

MOUNTING

SURFACE

Hand tighten LOCKNUT (11) to secure VALVE BODY (8).

Repeat above steps for opposite VALVE BODY (8A).

Install LOCKNUT (11) onto VALVE BODY (8).

From under side of mounting surface, install VALVE BODY (8) through valve

mounting holes. Threads of VALVE BODY (8) should extent at least 5/16

of a inch above mounting surface top. Fig. B. Thread ESCUTCHEON (10)

onto VALVE BODY (8) until snug against internal stop. If necessary, adjust

LOCKNUT (11).

Place RUBBER RING (9) into SCUTCHEON (10).

5/16'' MIN.

Fig. B.

To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.

Congratulations on purchasing your American Standard

faucet with Speed Connect drain, a feature found only on

American Standard faucets.

*Your new American Standard faucet is designed to work only with the Speed Connect drain.

Speed Connect Drain*

• Fewer parts, installs in less time

• Never needs adjustment

• Guaranteed to seal properly the ﬁrst time, every time.

1 2 3 4 5 6

Summary of Contents

Page 1 - Instructions

46127871 SERIES5SLOTTurn off hot and cold watersupplies before beginning.CAUTIONInsert SPOUT (1) and CABLE CONNECTOR (12) through center hole, making

Page 2 - REAR OF SINK

61POP-UP KNOB (1) must be fully down. Fig. B. FLANGE GASKET AND POP-UP KNOBDOWNWHITE FOAMGASKETNOT VISIBLEDRAINFLANGEFig. A. Fig. B.Check DRAIN FLANG

Page 3 - CHECK OPERATION OF POP-UP

Connect HOT water supply to inlet of left SHANK and COLDwater supply to right SHANK using sealant, appropriateconnectors, and COUPLING NUTS.Connect 1-

Page 4 - HANDLE ONLY)

INSTALL HANDLES (Lever) INSTALL HANDLES (Cross)CHECK DRAIN CONNECTIONS11121314TEST INSTALLED FITTINGWith HANDLES (1) in OFF position, turn on WATERSUP

Page 5 - Speed Connect™ Drain

Speed Connect™ DrainTroubleshooting GuideDisconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.Look at th

Page 6 - US60404 Rev. 1.2

STOPPER INSTALLATION PROCEDURELocked Mode: Look at the Plastic Loop at the bottom of the Stopper and noticethat the Loop is on one side of the Stopper

Comments to this Manuals

No comments

American Standard Hampton 7881.702 User Manual

Browse online or download User Manual for Sanitary ware American Standard Hampton 7881.702. American Standard Hampton 7881.702 User's Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Sanitary ware American Standard Hampton 7881.702