American Standard 7501.170.002 Installation Guide download pdf

CENTERSET LAVATORY FAUCETS

WITH GOOSENECK SPOUT

Installation

Instructions

7500 Series

7501 Series

7502 Series

7545 Series

Thank you for selecting American-Standard...

the benchmark of ﬁne quality for over 100 years.

To ensure that your installation proceeds smoothly--

please read these instructions carefully before you begin.

Certiﬁed to comply with ANSI A112.18.1M

60185 Rev. 1.6

TEST INSTALLED FAUCET

Remove AERATOR.

With handle in OFF position, turn on water supplies and check

all connections for leaks.

Operate both handles to ﬂush water lines thoroughly. Check

spout mounting and hose connections for leaks.

Operate LIFT ROD and check DRAIN for leaks.

Turn handles into OFF position and replace AERATOR.

Apply a bead of PUTTY around underside

of DRAIN PLUG FLANGE (1). Insert DRAIN

PLUG (2) into SINK drain hole.

Hold DRAIN PLUG (2) to prevent turning

and assemble GASKET (3), WASHER (4)

and LOCKNUT (5) from underneath sink.

Insert threaded end of TAILPIECE (6)

into lower end of DRAIN PLUG (2).

Connect other end to trap.

GRID DRAIN ASSEMBLY

(Model 7502 only)

PUTTY

SINK

PUTTY

Asesemble GASKET (1) to SHANKS (2) and insert FAUCET SHANKS through holes of SINK.

Assemble RUBBER (3) and BRASS WASHERS (4), and LOCKNUTS (5) from underside of SINK. Drop

UPPER LIFT ROD (6) through hole in BODY (models 7501 only), align BODY as far forward as possible

and secure position by tightening LOCKNUTS (5).

Connect the HOT water supply to the left SHANK and the COLD water supply to the right

SHANK using sealant, appropriate connectors, and COUPLING NUTS (7).

Unscrew SPOUT NUT (8) and remove SPOUT (9).

To change spout to a swivel spout: (7500, 7501 & 7502)

Take SPOUT CLIP (10) off SPOUT (9) and remove RUBBER RING (11).

Replace RUBBER RING (11) with seperate PLASTIC RING (12) packed with faucet.

Put SPOUT CLIP (10) on SPOUT.

Reassemble SPOUT (9) to BODY.

BODY

SINK

HOT

COLD

1/2" O.D. SLIP

INSTALL POP-UP DRAIN

(Model 7501 only)

Push TAILPIECE (1) down into TRAP

(threaded end up).

Thread LOCKNUT (2), WASHER (3) and

GASKET (4) onto DRAIN BODY (5).

Apply a bead of PUTTY to underside

of FLANGE (6).

Feed DRAIN BODY (5) up through SINK

and thread FLANGE (6) fully onto BODY (5).

Tighten LOCKNUT (2) ﬁrmly, keeping the

PIVOT ROD (7) pointed towards the back

of the SINK.

Drop STOPPER (8) into DRAIN BODY (5).

Pull TAILPIECE (1) up and thread tightly

into DRAIN BODY (5).

Position EXTENSION ROD (9) onto POP-UP

ROD (10) and tighten THUMBSCREW (11).

Remove one end of CLIP (12) from PIVOT ROD (7)

by squeezing ends together while sliding.

Insert PIVOT ROD (7) into second or third hole

in EXTENSION (9) and reassemble CLIP (12).

(EXTENSION may need to be bent.)

Adjust STOPPER (8) height by repositioning

EXTENSION and tightening THUMBSCREW (12).

TRAP

Turn off water at

main supply.

CAUTION

1 2

Summary of Contents

Page 1 - Instructions

CENTERSET LAVATORY FAUCETSWITH GOOSENECK SPOUTInstallationInstructions7500 Series7501 Series7502 Series7545 SeriesThank you for selecting American-Sta

Page 2 - 7545 Series

7500 Series7501 Series7502 Series7545 SeriesSERVICE5CARTRIDGESCREENTo change direction of handle rotation, proceed as follows:Turn valve to OFF positi

Comments to this Manuals

No comments

American Standard 7501.170.002 Installation Guide

Browse online or download Installation Guide for Faucets American Standard 7501.170.002. American Standard 7501.170.002 Installation Guide User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Faucets American Standard 7501.170.002